Funded startups with no in-house electronics
- You have a product idea and need a first prototype.
- You need firmware and electronics designed together.
- You need a path from prototype to production.
Firmware and hardware design for electronic products
From idea to prototype to production
We design your product's electronics and firmware, build and test the prototype and prepare it for production, all under one roof.
For startups, manufacturers and design firms that need firmware and electronics help, without a full-time hire.
- Free consultationabout your project's feasibility
- 10 years of experiencein firmware and electronics design
- No surprise costsWritten scope and fixed price
- Canadian corporationGST registered
How we take your product from idea to production
Start at any stage. We can take your product all the way, or pick up one defined piece of the work.
-
Stage 1
Idea
Start with a free consultation about your project's feasibility. We then put the scope, price and milestones in writing, so the work is clear before design starts.
You receive
- Free feasibility consultation
- Written scope, price and milestones
-
Stage 2
Prototype
We design the schematics, PCB and firmware together, with the PCB made to fit an off-the-shelf housing. Then we get the boards working and test them, with regular updates along the way.
You receive
- Working, tested prototype boards in an off-the-shelf housing
- Schematics and source code
- Test notes
-
Stage 3
Production
We prepare the design for manufacture, with production testers, test rigs, sensor calibration and direct work with suppliers and PCB manufacturers.
You receive
- Production testers and test rigs
- Source code, schematics, test notes and documentation at handover
Not sure your project is feasible?
Start with a free consultation.
Who this is for
Common situations where companies need this help.
Small manufacturers updating products
- An existing product needs a firmware or electronics update.
- You want to add wireless features or remote software updates.
- Sensor readings drift or don't repeat.
Design firms with overflow work
- You want to hand off one defined piece of firmware or electronics design.
- New boards need testing and debugging.
- A project needs a test rig, production tester or test software.
Firmware and electronics design for your product
The work hardware products need, without a full-time hire.
Product firmware
The software that runs inside your product and controls how it works.
Secure software updates
Send fixes and new features to your products safely, even after they ship.
Circuit board design
The electronics inside your product, from the first schematic to a finished board.
Low-power, battery-powered design
Electronics and firmware that use as little power as possible, so the battery lasts longer and your product can stay small.
IoT and connected devices
Connect your product to phones, networks and other equipment, by wire or wirelessly.
Motor control
Electronics and firmware that drive and control electric motors.
Power supplies
Power supplies designed as part of your product's electronics.
Sensors and calibration
Calibration that helps your sensors stay accurate and give repeatable readings.
Testing and production tools
Getting your first boards working, then building the equipment that tests your product.
Every step under one roof
You have one point of contact for hardware, firmware, housing and production, so you don't need to work with different companies.
Problems often sit between hardware and firmware. Because we design both, we can look for the real cause on both sides.
Working with us
Clear terms in writing, regular updates, and a handover at the end.
- Written scope
- Scope, price and milestones are set out in writing.
- Fixed price or hourly
- We work to fixed-price milestones or hourly.
- Regular updates
- You get regular updates while the work is under way.
- Remote and part-time
- Remote, part-time project work.
- Suppliers and manufacturers
- We deal directly with suppliers and PCB manufacturers for you.
- Canadian corporation
- Rasa Electronics Inc. is a Canadian corporation, GST registered.
Start with a free consultation
Tell us what you want to build or improve, and where it stands today.
Request your free consultation
Use this form to request a free consultation about your project.
What happens next
- You send the form.
- We reply with next steps for your free consultation.
- If you decide to go ahead, you receive a written scope, price and milestones.
Prefer email?
info@rasaelectronics.com